ADJUST (Adjustment mode)
■ ADJ-XY
COPIER (Service mode for copier) > ADJUST (Adjustment mode) > ADJ-XY
ADJ-X
Adj start pstn in book mode: vert scan
Detail
To adjust the image reading start position (image leading edge position) in the vertical scanning
direction at copyboard reading.
When replacing the Main Controller PCB, enter the value of service label.
Decrease the value when the non-image width is larger than the standard value.
Increase the value when out of original area is copied.
As the value is incremented by 1, the image position is moved to the trailing edge side by 0.1 mm.
Use Case
- When replacing the Reader Unit
- When replacing the Scanner Unit
- When replacing the Main Controller PCB
Adj/Set/Operate Method
Enter the setting value (switch negative/positive by +/- key), and then press Apply key.
Caution
After the setting value is changed, write the changed value in the service label.
Display/Adj/Set Range
-30 to 30
Unit
0.1 mm
Default Value
0
ADJ-Y
Adj start pstn in book mode: horz scan
Detail
To adjust the image reading start position in the horizontal scanning direction at copyboard reading.
When replacing the Main Controller PCB, enter the value of service label.
Decrease the value when the non-image width is larger than the standard value.
Increase the value when out of original area is copied.
As the value is incremented by 1, the image position is moved to the rear side by 0.1 mm.
Use Case
- When replacing the Reader Unit
- When replacing the Scanner Unit
- When replacing the Main Controller PCB
Adj/Set/Operate Method
Enter the setting value (switch negative/positive by +/- key), and then press Apply key.
Caution
After the setting value is changed, write the changed value in the service label.
Display/Adj/Set Range
-15 to 15
Unit
0.1 mm
Default Value
0
ADJ-Y-DF
Adj start pstn: stream, horz scan, front
Detail
To adjust the front side image reading start position in horizontal scanning direction at stream
reading.
When replacing the Main Controller PCB, enter the value of service label.
As the value is incremented by 1, the image position is moved to the front side by 0.1 mm.
Use Case
- When replacing the DADF
- When replacing the Scanner Unit
- When replacing the Main Controller PCB
Adj/Set/Operate Method
Enter the setting value (switch negative/positive by +/- key), and then press Apply key.
Caution
After the setting value is changed, write the changed value in the service label.
Display/Adj/Set Range
-15 to 15
Unit
0.1 mm
Default Value
0
9. Service Mode
243
Summary of Contents for MF735C Series
