Canon J1, Service Manual

Page: 113 / 140

5
5
5-15
5-15
Adjustment > Basic Adjustment > Function Setting Operation
Adjustment > Basic Adjustment > Function Setting Operation
Function Setting Operation
The following are items of the function setting and use scenes.
The setting procedure is as follows.
NO Item Use case
[1] Setting the Upward Curl Prevention
Mode
When the upper curl occurs on the paper
delivered to the stack tray.
[2] Setting the Downward Curl Prevention
Mode
When the lower curl occurs on the paper
delivered to the stack tray.
[3] Setting the Thick Paper Curl
Prevention Mode
When the upper curl occurs at the thick paper
delivery.
[4] Setting the Thick Paper Pushing
Forward Prevention Mode
When the previous delivery paper is pushed by
the next delivery paper.
[5] Setting the Poor Offset Stacking
Prevention Mode
When the stack fault occurs in the small paper
offset mode.
[6] Setting the Poor Stacking of Thin
Paper Prevention Mode
When the stack fault occurs with the thin
paper.
[7] Setting the Staple Stack Position
Change Prevention Mode
When the top paper is displaced in the stapling
delivery mode.
[8] Setting the Tray Switching Noise
Reduction Mode
When the switch sound for the stack tray shift
is noisy.
[9] Setting the Tray Switching Speedup
Mode
When the switch time for the stack tray shift is
long.
[10] Setting the Finisher Noise Reduction
Mode
When the movement sound for the finisher is
noisy.
[11] Setting the 1-Sheet Shift Sort Enabled
Mode
When the 1-sheet shift sort enabled mode is
necessary.
[12] Setting the Saddle Stacking Capacity
Switching Mode
When large/thin paper is not appropriately
stacked.
[13] Setting the Saddle Stack Alarm
Detection Disabled Mode
When the paper delivered with non-sort mode
is not appropriately stacked.
[14] Poor Large/Thin Paper Stack
Prevention Mode
When large/thin paper is not appropriately
stacked.
[15] Poor Non-Sort Delivery Stack
Prevention Mode
When the paper delivered with non-sort mode
is not appropriately stacked.
[16] Set Occasional Misalignment
Prevention Mode
When misalignment in feed direction occurs
occasionally for thin/plain paper.
[17] Change of Paper Stack Speed for
Buffered Paper Mode
When the alignment failure occurs in the sort
or staple mode.
[18] Setting Finisher Buffer Operation
Mode
When misalignment of paper stack occurs in
staple mode for small size papers.
T-5-3
1) Turn off the host machine.
2) Remove the rear cover of finisher.
3) Set the bits of DSW1 on the finisher controller PCB as follows:
ON
1 2 3 4 5 6 7 8
4) Turn on the host machine.
5) Set the DSW1 on the finisher controller PCB as follows.
NO Item Bit setting of DSW1 in the
finisher controller PCB
[1] Setting the Upward Curl Prevention Mode ON:2
[2] Setting the Downward Curl Prevention Mode ON:2,8
[3] Setting the Thick Paper Curl Prevention Mode ON:2,7
[4] Setting the Thick Paper Pushing Forward Prevention Mode ON:2,7,8
[5] Setting the Poor Offset Stacking Prevention Mode ON:2,6
[6] Setting the Poor Stacking of Thin Paper Prevention Mode ON:2,6,8
[7] Setting the Staple Stack Position Change Prevention Mode ON:2,5
[8] Setting the Tray Switching Noise Reduction Mode ON:2,5,6
[9] Setting the Tray Switching Speedup Mode ON:2,5,6,7
[10] Setting the Finisher Noise Reduction Mode ON:2,5,6,8
[11] Setting the 1-Sheet Shift Sort Enabled Mode ON:2,4
[12] Setting the Saddle Stacking Capacity Switching Mode ON:2,4,8
[13] Setting the Saddle Stack Alarm Detection Disabled Mode ON:2,4,7
[14] Poor Large/Thin Paper Stack Prevention Mode ON:2,6,7
[15] Poor Non-Sort Delivery Stack Prevention Mode ON:1,2,5,6,7,8
[16] Set Occasional Misalignment Prevention Mode ON:2,6,7,8
[17] Change of Paper Stack Speed for Buffered Paper Mode ON:2,5,7
[18] Setting Finisher Buffer Operation Mode ON:2,5,8
F-5-26
T-5-4