Chapter 8
8-26
2F16
Hardware error.
03130031-2F16
Turn off printer,
wait, then
turn on again.
Power On
Again
Mist Fan Error
Mist fan error
The rotation of the mist fan is not
detectable.
1. Check the bundled wires in the mist
fan drive circuit.
2. Replace the mist fan unit.
3. Replace the main controller PCB.
2F17
Hardware error.
03130031-2F17
Turn off printer,
wait, then
turn on again.
Power On
Again
Platen Fan Lock
Platen fan lock detection error
The lock signal has been supplied
continuously for 3 seconds or longer, 10
seconds after the platen fan started rotating.
1. Check the bundled wires in the
platen suction fan drive circuit.
2. Replace the platen suction fan unit.
3. Replace the main controller PCB.
Power On
Again
Platen Fan Err
2F1F
Hardware error.
03130031-2F1F
Turn off printer,
wait, then
turn on again.
Power On
Again
Purge Motor
Sensor Error
Purge sensor error (recovery purge motor
HP detection error)
The recovery system has been driven but
no sensor interrupt occurs.
The recovery system has been driven to
close the cap, but the cap has not been
capped successfully.
2F20
Hardware error.
03130031-2F20
Turn off printer,
wait, then
turn on again.
Power On
Again
Motor Cam Pos
Error
Cap motor cam positioning error
The recovery system has been driven but
no sensor interrupt occurs.
The recovery system has been driven to
close the cap, but the cap has not been
capped successfully.
2F21
Rel lever is in
wrong position.
Turn off printer,
wait, then
turn on again.
Pinch roller open detected with the pinch
roller locked.
1. Restart with the pinch roller closed.
2. Check the sensor in I/O DISPLAY
in Service mode (Check the pinch
roller pressure release detection SW/
the release lever lock sensor.)
2F22
Hardware error.
03130031-2F22
Turn off printer,
wait, then
turn on again.
Power On
Again
Pump Motion
Timeout
Pump shift timeout
The target position could not be reached
within a predicted operation time +3
seconds during pump operation or no
sensor has been detected during a pump
operation involving sensor detection.
<Supplement>
-If the carriage travels heavily towards
the stop position: A mechanical load
error may be suspected.
-Otherwise: The sensor in the purge
unit may be at fault.
2F23
Hardware error.
03130031-2F23
Turn off printer,
wait, then
turn on again.
Power On
Again
Pump Motion
Error
Purge motor error
A PWM duty of 100% has lasted for 200
msec in a pump operation.
<Supplement>
-If the motor could not be run at all or
has resulted in an error after moving by
a slight distance:
A. A mechanical load error may be
suspected.
B. The motor or drive circuit may be at
fault.
-If the carriage has run more or less out
of control and resulted in an error:
A. The encoder sensor may be at fault.
2F24
Cannot cut paper.
Lift the release
lever and reload
the paper.
Cutting Error
Please Cut Papr
Press (upper arrow) Key
to Release Paper
Cutter shift timeout
The cutter failed to reach the home position
in time during a cutting operation
2F24
Hardware error.
03130031-2F24
Turn off printer,
wait, then
turn on again.
Power On
Again
Cutter Timeout
Cutter shift timeout error
No sensor has been detected during a cutter
operation involving sensor detection.
2F25
Hardware error.
03130031-2F25
Turn off printer,
wait, then
turn on again.
Power On
Again
CR Position Err
Restart Printer
Carriage motor HP not detectable
Detected only for the wide format.
For the narrow format, the carriage motor
HP can be detected when the carriage hits
the wall in a full scan following the
detection of the HP.
Check the carriage HP sensor in I/O
mode.
<Supplement>
-If the motor could not be run at all:
A. A mechanical load error may be
suspected.
B. The motor or drive circuit may be at
fault.
-If the carriage has resulted in an error
after moving at a constant speed:
A. The carriage HP sensor may be at
fault.
-If the carriage has run more or less out
of control and resulted in an error:
A. The encoder sensor may be at fault.
2F26
Hardware error.
03130031-2F26
Turn off printer,
wait, then
turn on again.
Power On
Again
Carriage Motion
Error
Carriage operation disabled
-A PWM duty of 100% has lasted for 200
msec in a carriage operation
-A collision has been detected in a carriage
operation (with the speed predicted from
the PWM output value having a deviation
of 25 ips or more from the actual speed).
<Supplement>
-If the motor could not be run at all or
has resulted in an error after moving by
a slight distance:
A. A mechanical load error may be
suspected.
B. The motor or drive circuit may be at
fault.
-If the carriage has run more or less out
of control and resulted in an error:
A. encoder sensor may be at fault.
Code
(last 4 digits)
Panel display
(Large LCD)
Panel display
(Small LCD)
Explanation/Detection sequence
Remedial Action
Summary of Contents for iPF825
