Chapter 8
8-7
200F
This paper
cannot be used.
Check supported
paper sizes.
Paper Size
Please Check
Paper Too Large
Paper mismatch (size)
Paper is too large
-The width and length of paper detected are
longer than the supported size (1.5%
margin).
-Cannot detect the leading edge of paper
even when the paper has been fed by 1300
mm for roll paper and by the size
mentioned above for cut sheet.
-Cannot detect the width of paper even
when the paper is fed by the size mentioned
above.
1. Check paper conditions (soiling,
tear-offs, residual paper chips, residual
trimming cuts, folds)/size.
2. Has the paper been fed successfully
(without slippage under a load or any
influence)?
3. Has the LF adjustment value set
correctly?
4. Hasn't the loaded paper shrunk to
below its margin in the particular
environment?
This paper
cannot be used.
Check supported
paper sizes.
Load/Eject: Change Paper
Paper Too Large
Please Check
Press Online Key
and Reload
2010
Paper loaded askew.
Press Load/Eject
and reload the
paper.
Paper Askew
Please Reload
Paper Skew
Skew (skewed right)
Paper is determined skewed as its edge is
read by the multisensor.
Reload the paper.
Paper loaded askew.
Reload the paper.
Paper Loaded
Crooked
Press Online Key
and Reload
Paper loaded askew.
Lift the
release lever.
Paper loaded
askew.
Remove paper
Paper loaded askew.
Lift the release
lever and reload
the paper.
Paper loaded askew.
Press OK and
reload the paper.
Paper loaded askew
Lift the release lever.
2015
Cannot cut paper.
Press Load/Eject
and reload the
paper.
<When small LCD 1>
Cutting Error
Please Cut Papr
<When small LCD 2>
Press (upper arrow) Key
to Release Paper
Cutting failure/jam detected due to a
cutting failure
An idle cutter unit or a cutter blade that is
too blunt to cut sheet has been detected by
the paper leading edge detection sequence.
Cannot cut paper.
Reload the paper.
Cannot cut paper.
Lift the release
lever and reload
the paper.
Paper cutting
failed. Lift the
release lever.
2016
No sheets.
Press Load/Eject
and reload the
paper.
Sheets
Please Load
Sheet Not Loaded
Paper loosened out of position while
printing
The trailing edge of paper has been
detected at least 20 mm shorter than the
length of cut forms detected.
Reload the paper.
No sheets.
Lift the release
lever and reload the sheets.
The paper is too
small.
Check paper size.
Sheet removed.
Lift the release
lever.
Paper jam.
Press Load/Eject and reload
the
paper.
Paper Jam
Press (upper arrow) Key
Jam while picking up, ejecting or printing
on paper
(A sequence of removing jams with the
pinch roller released is required)
Virtually all recovery errors that could
occur in connection with paper pickup are
handled.
1. Open and close the release lever to
reload the paper.
2. Remove the paper once and then
refeed it.
Paper jam.
Manually rewind roll
all the way.
Paper Jam
Press (upper arrow) Key
Paper Eject Err
Remove Paper
Paper jam.
Manually rewind roll
all the way
and press OK.
Cannot feed paper
Lift the release
lever and reload paper.
Cannot feed paper.
Reload the paper.
Cannot feed paper.
Press Load/Eject
and reload the
paper.
Code
(last 4 digits)
Panel display
(Large LCD)
Panel display
(Small LCD)
Explanation/Detection sequence
Remedial Action
Summary of Contents for iPF825
