Canon ImageCLASS MF4690 Service Manual Download Page 81 | Manualshive

Page: 81 / 182

background image

Chapter 7

7-5

7.4 Duplex Unit

7.4.1 Overview

0016-1856

The duplexing pick up operation of this machine is performed by the drive of the main motor (M1) under CPU control of the DCNT board.
After the machine completes the 1st print and the paper's trailing edge passes over the delivery sensor (PS803), the duplexing drive solenoid (SL2) is turned on and
the drive of the main motor (M1) is transmitted to the delivery roller and the duplexing feed roller.
By turning the delivery roller in reverse direction, the paper is lead to the duplexing feed unit, and sent to the feed roller via duplexing feed roller.
There is no sensor on the duplexing paper's feeding path to detect the arrival/passage of paper.
There is no stationary function to stop and retain paper in duplexing unit.

F-7-4

M1

SL2

PS803

«
...
79
80
81
82
83
...
»

Summary of Contents for ImageCLASS MF4690























































































































































































Reviews:

No comments

Related manuals for ImageCLASS MF4690

Documax A6300 Series

Brand: DataSouth Pages: 180

5550B - Phaser B/W Laser Printer

Brand: Xerox Pages: 117

WorkCentre 3345

Brand: Xerox Pages: 18

Aficio SP C730DN

Brand: Ricoh Pages: 100

SignJet JS310 Series

Brand: GRAPHTEC Pages: 83

Brand: Xerox Pages: 85

Brand: Oki Pages: 220

varioPRINT 6000 TITAN Series

Brand: Canon Pages: 69

Brand: Canon Pages: 224

Brand: Canon Pages: 29

Brand: Lexmark Pages: 2

Brand: Fujitsu Pages: 2

Brand: Dell Pages: 4

Brand: Dell Pages: 68

Ink-Free Printer PZ310

Brand: Dell Pages: 22

Brand: Dell Pages: 124

5330dn - Workgroup Laser Printer B/W

Brand: Dell Pages: 204

Brand: Dell Pages: 216

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands