Canon ImageCLASS MF4690 Service Manual Download Page 162 | Manualshive

Page: 162 / 182

background image

Chapter 14

14-22

14.10.3 System Dump List

0016-2113

- System Dump List
Use it to check the history of communications, both successful and error.

F-14-4

*1: TX, number of total pages transmission.
*2: Total number of pages transmitted/received according to original size.
*3: RX, number of total pages reception.
*4: Total number of pages transmitted and received for each modem speed
*5: Total number of pages transmitted/received in connection with different modem speeds (Standard, Fine, Super Fine, Ultra Fine).
*6: Total number of pages transmitted and received for each coding method
*7: Total number of pages transmitted and received in each mode
*8: Total number of pages printed/scanned
*9: Total number of occurrences for error code

T-14-20

It provides error information on the 3 most recent communications.

Indication

sample

##280

1

7

3

0

0

##280

number of errors

##281

number of errors

##282

number of errors

[1]

[3]
[2]

[3]

[4]

[5]
[6]

[7]

[8]

[9]

«
...
160
161
162
163
164
...
»

Summary of Contents for ImageCLASS MF4690























































































































































































Reviews:

No comments

Related manuals for ImageCLASS MF4690

Brand: Duplo Pages: 123

Brand: Oce Pages: 306

Brand: Printek Pages: 31

Brand: Intermec Pages: 38

Brand: Star Pages: 82

Brand: MAC TOOLS Pages: 2

Brand: Tally Pages: 106

Brand: EFI Pages: 4

Brand: AstroJet Pages: 32

Brand: Oki Pages: 182

Brand: Olivetti Pages: 97

4650NX - SuperScript Color Laser Printer

Brand: NEC Pages: 74

ECOSYS FS-C2526MFP

Brand: Kyocera Pages: 36

Brand: Oki Pages: 181

Brand: Canon Pages: 1154

Brand: Oki Pages: 76

Tektronix Phaser 2135

Brand: Xerox Pages: 2

Brand: VIP Color Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands