Canon ImageCLASS MF4690 Service Manual Download Page 87 | Manualshive

Page: 87 / 182

background image

Chapter 8

8-1

8.1 Overview/Configuration

8.1.1 Specification/Control/Function List

0016-1857

T-8-1

8.1.2 Overview

0016-1858

The fixing unit employees the on-demand fixing method, and it is composed of fixing film unit, in which the fixing heater, thermistor, and temperature fuse are
incorporated, and the pressure roller.
The pressure roller and the delivery roller are driven with the main motor (M1).
A paper separated from the photosensitive drum is fed to inside of the fixing assembly, and the toner is fixed on a paper with the fixing film and the pressure roller.
A paper being fixed is detected with the delivery sensor (PS803); then, delivered to outside of the machine via the delivery roller.

F-8-1

[1] Pressure roller
[2] Fixing film
[3] Delivery roller
H1: Fixing heater
PS803: Delivery sensor

The fixing heater is the heater (ceramic heater) that the heating pattern is deposited on the ceramic plate.
By heating the fixing film with the fixing heater, it gives heat to passing papers.
The thermistor (TH1) locates at the center of the fixing heater (H1), and detects the temperature of the heater.
The temperature fuse (TP1) locates at the top center of the fixing heater. If the temperature of the fixing heater increases abnormally, it blocks power supply to the
heater by meltdown.
The temperature control of the fixing assembly composed of the foregoing components is executed at the fixing control circuit on the DCNT board with the instruc-
tion of the CPU (IC902). There are the fixing heater drive circuit and the fixing heater safety circuit in the fixing control circuit.

Item Function/Method

Fixing method

On-demand fixing

Fixing heater

Flat heater

Fixing temperature detection

Thermistor (TH1): temperature control, detection of abnormality

Temperature fuse (TP1): detection of abnormality

Fixing temperature control

Temperature control at startup

Temperature control at normal times

Temperature control at sheet-to-sheet interval

Protection function

Temperature error detection with the thermistor

Temperature rise detection with the temperature fuse

«
...
85
86
87
88
89
...
»

Summary of Contents for ImageCLASS MF4690























































































































































































Reviews:

No comments

Related manuals for ImageCLASS MF4690

Brand: Oki Pages: 24

Brand: VAF instruments Pages: 24

Brand: DataCard Pages: 17

Brand: DataCard Pages: 24

Brand: Nanoptix Pages: 25

Brand: Nanoptix Pages: 4

Brand: Canon Pages: 4

Brand: Lexmark Pages: 2

Brand: BIXOLON Pages: 59

Brand: Xerox Pages: 20

5550N - Phaser B/W Laser Printer

Brand: Xerox Pages: 16

VarioLink 2650cp

Brand: Oce Pages: 2

Brand: Printekmobile Pages: 2

Brand: Lexmark Pages: 221

Brand: Sam4s Pages: 24

Brand: Konica Minolta Pages: 7

Brand: WOOSIM Pages: 19

ImageRUNNER ADV

Brand: Canon Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands