Canon ImageCLASS MF4690 Service Manual Download Page 170 | Manualshive

Page: 170 / 182

background image

Chapter 14

14-30

G3 Signal Transmission Test

A press on '4' on the keypad from the MODEM test menu selects the G3 signal transmission test. In this test, the following G3 signals from the modem are trans-
mitted using the telephone line terminal and the speaker. To select a different transmission speed, use the keypad.

MEMO:

The output level of individual signals is in keeping with the setting made in service mode.

DTMF Signal Transmission Test

A press on '5' on the MODEM test menu selects the DTMF signal transmission test. In the test, the following DTMF signals from the modem are transmitted using
the telephone line terminal and the speaker. The number pressed on the keypad selects a specific DTMF signal.

MEMO:

The output level of individual signals is in keeping with the setting made in service mode.

Tonal/DTMF Signal Reception Test

A press on '6' on the keypad from the MODEM test menu selects the tonal signal/DTMF signal reception 0 test. In this signal, the tonal signal/DTMF signal received
from the telephone line terminal can be checked to find out if it was detected by the modem.

F-14-11

V.34 G3 Signal Transmission Test

A press on '8' on the keypad from the MODEM test menu selectes the V.34 G3 signal transmission test. The V.34 G3 signals below are sent from the modem using
the modular jack and the speaker by pressing the start key. The Baud rate can be changed with the keypad, and the Speed can be changed with the left/right arrow
key.

Keypad

Transmission speed

0

300bps

1

2400bps

2

4800bps

3

7200bps

4

9600bps

5

TC7200bps

6

TC9600bps

7

12000bps

8

14400bps

Keypad

Baud rate

0

3429baud

1

3200baud

2

3000baud

3

2800baud

4

2743baud

5

2400baud

Left/right arrow key

Transmission speed

2400bps

4800bps

7200bps

9600bps

MODEM TEST
OFF OFF OFF

OFF OFF OFF

changes from '0' to '1' in response to detection of a signal of 462

25 Hz.

changes from '0' to '1' in response to detection of a signal of 1100

30 Hz.

changes from '0' to '1' in response to detection of a signal of 2100

25 Hz.

Tonal signal reception test

MODEM TEST
OFF OFF OFF 5

DTMF signal reception test

The received DTMF signals are indicated starting
from the right using the 2nd character of the display.

«
...
168
169
170
171
172
...
»

Summary of Contents for ImageCLASS MF4690























































































































































































Reviews:

No comments

Related manuals for ImageCLASS MF4690

Brand: GCC Technologies Pages: 14

Brand: Xerox Pages: 168

Brand: Xerox Pages: 36

Brand: Xerox Pages: 64

Brand: Xerox Pages: 54

Brand: Xerox Pages: 2

Brand: Xerox Pages: 115

Brand: UltraTape Pages: 52

Brand: Xerox Pages: 93

Brand: Xerox Pages: 36

Copycentre C118

Brand: Xerox Pages: 12

Brand: Xerox Pages: 136

4250 - WorkCentre - Copier

Brand: Xerox Pages: 4

4250 - WorkCentre - Copier

Brand: Xerox Pages: 4

Brand: Xerox Pages: 8

4150 - WorkCentre B/W Laser

Brand: Xerox Pages: 4

4150 - WorkCentre B/W Laser

Brand: Xerox Pages: 40

4150 - WorkCentre B/W Laser

Brand: Xerox Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands