ELURA20 MC A, ELURA10 A
CHAPTER 1. GENERAL DESCRIPTION OF PRODUCT
1-48
7-9 Using Analog Line, DV Recording
(1) Set the power switch to [VCR].
The Power LED (green) will light and, if a cassette is loaded, standby status will be activated. The jack (DVAS-video, AV mini)
status will be output, and headphone jack (with Docking Unit DU-300 connected) and speaker will be output (higher priority in
headphone).
(2) Connect a cable from a recording source to the S-video jack* (video signal) and AV mini jack (audio signal), or to the AV mini jack
(video and audio signals), or to the DV jack; then turn on the recording source power supply.
If the recording source is connected to multiple jacks at the same time, the recording source is automatically selected in following
jack priority.
DV Jack> S-video Jack * > AV Jack * : (with Docking Unit DU-300 connected)
During playback (including special play), the playback image will have a higher priority.
(3) On the remote control, press [REC STANDBY].
Recording pause status will be activated. In the case of analog line input, the S-video jack and AV mini jack will switch to input.
(4) To start recording, press [ / ] of the remote controller.
Recording of the video and audio from the jack selected in item (2) will start.
([ / ] toggles the record and record pause operations.)
(5) Press [
■
] to stop recording.
Recording will stop.
The Table below Shows the Input and Output Status for Each Mode.
* There is no signal when there is no line input.
7-10 VIdeo ID1 Detection/Output Capability
(1) S1 signal output
When 16:9 images are output from the S-video jack in the Full (Squeeze) mode compressed to 4:3, an identification signal is output
to automatically return them to 16:9 images for wide monitors with S1 capability (when tape on which is recorded system data
related to the camera 16:9 mode or aspect ratio is played back.)
• NTSC
→
16:9 full mode + 4:3 letterbox mode identification signal output
(2) Video ID1 output
When 16:9 images are output from the composite video jack in the Full (Squeeze) mode compressed to 4:3, an identification signal
is output to automatically return them to 16:9 images for wide monitors with Video ID1 capability (when tape on which is recorded
system data related to the camera 16:9 mode or aspect ratio is played back.)
(3) S1 signal and video ID1 detection with line input
When video ID1 and S1 signals superimposed over video signals from the composite video jack or S-video jack are detected, the
system data related to aspect ratio is recorded.
DV input signal present
No DV input signal present
LCD/CVF
DV jack
S/AV jack
LCD/CVF
DV jack
S/AV jack
Playback
Playback screen
OUT
OUT
Playback screen
OUT
OUT
(including special playback)
No tape, STOP, FF, REW
DV input screen
IN
OUT
Blue background
OUT
OUT
REC PAUSE/PEG
DV input screen
IN
OUT
Line input screen *
IN
IN
Summary of Contents for ELURA10 A
Page 150: ...5 16 ELURA20 MC A ELURA10 A CVF Unit Section 15 14 9 8 13 12 11 6 5 1 2 3 4 7 16 17 10 ...
Page 152: ...5 18 DMC II Mechanical Chassis Section 1 1 4 2 3 6 7 10 11 12 5 4 2 3 8 9 Slide Chassis Ass y ...
Page 158: ...5 24 DMC II Mechanical Chassis Section 4 REAR FACE 1 2 2 5 6 7 8 9 5 10 11 12 1 13 14 3 4 ...