manualshive.com logo in svg

Can-Am Roadster RT-622 2010, Service Manual

Share
Download
Can-Am Roadster RT-622 2010 Service Manual Download Page 31

Section 02 CHASSIS

Subsection 03 (BODY)

rmr2010-066-208_a

1. Bottom retaining screw
2. Plastic rivet

4. Remove top retaining screw.

rmr2010-066-209_a

1. Top retaining screw

5. Slightly push RH fascia forward to remove it

from trailer.

rmr2010-066-211

PUSH FASCIA FORWARD

LH and RH Inner Fascias Installation

The installation of the inner fascias is essentially
the reverse of the removal procedure.

RH inner fascia has to be installed first.

Finger tight all inner fascia screws.

FRONT ACCESS COVER

Front Access Cover Removal

1. Remove 4 retaining screws from front hinge.

rmr2010-066-240

FRONT HINGE ATTACHED WITH COVER

2. Remove front access cover from trailer.

3. If hinge has to be removed, open velcro flap to

access 4 retaining screws.

rmr2010-066-241

HINGE RETAINING SCREWS

Front Access Cover Installation

Installation is the reverse of removal procedure.

rmr2010-066

21

Summary of Contents for Roadster RT-622 2010





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands