background image

 

26

 

WARRANTY 

GENERAL 

Camus Hydronics Limited (“Camus”), extends the following LIMITED WARRANTY to the owner of this appliance, 
provided that the product has been installed and operated in accordance with the Installation Manual provided with 
the equipment. Camus will furnish a replacement for, or at Camus option repair, any part that within the period 
specified below, shall fail in normal use and service at its original installation location due to any defect in 
workmanship, material or design. The repaired or replacement part will be warranted for only the unexpired portion of 
the original warranty. This warranty does not cover failures or malfunctions resulting from: (1) Failure to properly 
install, operate or maintain the equipment in accordance with Camus’ manual; (2) Abuse, alteration, accident, fire, 
flood, foundation problems and the like; (3) Sediment or lime buildup, freezing, or other conditions causing 
inadequate water circulation; (4) Pitting and erosion caused by high water velocity; (5) Failure of connected systems 
devices, such as pump or controller; (6) Use of non-factory authorized accessories or other components in 
conjunction with the system; (7) failing to eliminate air from, or replenish water in, the connected water system; (8) 
Chemical contamination of combustion air or use of chemical additives to water. 

HEAT EXCHANGER 

If within TEN years after initial installation of the appliance, a heat exchanger, shall prove upon examination by 
Camus to be defective in material or workmanship, Camus will exchange or repair such part or portion on the 
following pro rated limited warranty. (1) Years one through five - standard warranty (2) Years six through ten - 
replacement purchase price pro rated at the following schedule: Year six - 60%, Year seven - 65%, Year eight -70%, 
Year nine -75% Year ten -80% of the current list price of the current list price This term is reduced to FIVE years if the 
appliance is used for other than hydronic space heating. 
Heat Exchanger shall be warranted for (20) years from date of installation against “Thermal Shock” (excluded, 
however, if caused by appliance operation at large changes exceeding 150 ºF between the water temperature at 
intake and appliance temperature, or operating at appliance temperatures exceeding 230 ºF). 
 

BURNER 

If within FIVE years after initial installation of the appliance a burner shall prove upon examination by Camus to be 
defective in material or workmanship, Camus will exchange or repair such part or portion. 
 

ANY OTHER PART 

If any other part fails within one (1) year after installation, or eighteen (18) months from date of factory shipment 
based on Camus' records, whichever comes first. Camus will furnish a replacement or repair that part. Replacement 
parts will be shipped f.o.b. our factory. 
  

HOW TO MAKE A CLAIM 

Any claim under this warranty shall be made directly to Camus Hydronics Limited Canadian Head Office 
 

SERVICE LABOR RESPONSIBILITY 

Camus shall not be responsible for any labour expenses to service, repair or replace the components supplied. Such 
costs are the responsibility of the owner. 
 

DISCLAIMERS 

Camus shall not be responsible for any water damage. Provisions should be made that in the event of a 
water/appliance or fitting leak, the resulting flow of water will not cause damage to its surroundings. 

 

 
Name of Owner 

 

 
Name of Dealer 

 

 
Address 

 

 
Address 

 

 
 

 

 

 

 
Model No. 

 

 
Serial No. 

 

 
Date of Installation: 

 

 
Date of Initial Operation: 

 

6226 Netherhart Road, Mississauga, Ontario, L5T 1B7, CANADA

Summary of Contents for MICOFLAME 2 Series






























Reviews: