Camplux CA686M-LP Page 27 Use & Care Manual Download

Page: 27 / 84

Wood Thread Screw

102mm(4.02”)

83mm(3.27”)

4-Ф0.24”

Base of Control

3. Replace the front cover on the remote control.

Electrical Connections

Power cord:

●

The electric power supply requirement for this water heater is 120 VAC/60HZ,

2 Amps.

●

The water heater comes with a three (3) pin power supply cord. Use only a

power outlet with a ground terminal.

●

The installation of an electric leakage breaker is recommended. (GFCI)

●

Keep any excess of the power supply cord on the outside of the water heater.

●

If local codes require hardwiring, see instructions for “Hardwiring the Electrical

Connections”.

WARNING: Shock hazard line voltage is present. Before servicing the

water heater, turn off the electrical power to the water heater at the main

disconnect or circuit breaker. Failure to do so could result in severe

personal injury or death.

Visit Us: Camplux.com

[email protected]

3330-A Marathon Ct Charleston, SC 29418

1(844) 538-7475

Summary of Contents for CA686M-LP





















































































Search results

Summary of Contents for CA686M-LP

Reviews:

Related manuals for CA686M-LP

Brands by name

Popular brands

Camplux CA686M-LP, Use & Care Manual

Search results

Summary of Contents for CA686M-LP

Reviews:

Related manuals for CA686M-LP

Brands by name

Popular brands