Camplux CA686M-LP Use & Care Manual Download Page 3

Page: 3 / 84

WA686M-NG/LP WA686MG-NG/LP

The *number will be replaced by (1-99) numbers, representing different decorative

patterns, and their internal structure is exactly the same.

CA686M-NG/LP CA686MG-NG/LP

The *number will be replaced by (1-99) numbers, representing different decorative

patterns, display shapes and display positions, and their internal structure is

exactly the same.

With Installation Instructions for the Installer

WA686M-NG WA686M-LP

WA686MG-NG WA686MG-LP

CA686M-NG CA686M-LP

CA686MG-NG CA686MG-LP

WARNING: If the information in these instructions is not followed exactly,

a fire or explosion may result causing property damage, personal injury

or death.

●

Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliances.

●

WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliances.

- Do not touch any electrical switch; do not use any phone in your

building.

Visit Us: Camplux.com

[email protected]

3330-A Marathon Ct Charleston, SC 29418

1(844) 538-7475

Summary of Contents for CA686M-LP





















































































Search results

Summary of Contents for CA686M-LP

Reviews:

Brands by name

Popular brands

Camplux CA686M-LP, Use & Care Manual

Search results

Summary of Contents for CA686M-LP

Reviews:

Brands by name

Popular brands