Camplux CA528 Use & Care Manual Download Page 23

Page: 23 / 44

Remote Control

Aviation Joint

www.camplux.com

(OPTIONAL) REMOTE CONTROL -

CONNECTION, INSTALLATION AND SET

(For Panel Control / Remote Control & Remote Control Units)

Panel Control/Remote Control and Remote Control units will work with either one or two remote controls. If

two remotes are desired, a wire connector will need to be provided. To connect the remote control.

1. For one control: Plug the aviation joint into the socket directly on the water heater (see illustration below)

2. For two controls: First, cut off the aviation joints on the two controllers, plug one into the socket on the water

heater (length is dependent on your requirements), and throw away the other. Then connect the wires of the

aviation joint to the inlet wire of the connector, and connect the two remote control to the outlet wires of

connector.

INSTALLATION OF REMOTE CONTROL

1. Remove the front cover of the Remote Control. (See illustration below)

2. At installation site, mark and screw two holes with 0.24” with 1.2” depth. Insert 2 rubber screws into the

holes. Place the remote control against the wall, align the holes of control with the holes in the wall, and fasten

them with wood thread screws. (See illustration below)

Remote Control

Control Base

Front Cover

Installation Hole

Visit Us: Camplux.com

[email protected]

3330-A Marathon Ct Charleston, SC 29418

(844) 538-7475

Summary of Contents for CA528













































Search results

Summary of Contents for CA528

Reviews:

Related manuals for CA528

Brands by name

Popular brands

Camplux CA528, Use & Care Manual

Search results

Summary of Contents for CA528

Reviews:

Related manuals for CA528

Brands by name

Popular brands