Campbell NL241 Product Manual Download Page 19

Page: 19 / 76

Typical Power Consumption (@ 12VDC)

Client Mode: 7.5 to 8 mA idle, 65 to 75 mA communicating

Access Point Mode: 67 mA idle, 70 mA communicating

Standby: less than 1.5 mA

NOTE:
Standby power is when the NL241 Wi-Fi power has been turned off. This state can be
enabled by configuration of the Mode button or by using the

IPNetPower()

data

logger instruction. See the CRBasic help for an example of using the

IPNetPower()

instruction. Note that the

IPNetPower()

instruction is only applicable when the NL241 is

configured with bridge mode enabled. See

Mode button

(p. 19) for information on the

Mode button configuration.

Operating Temperature

Standard: –40 to 70 °C

Configuration

Device Configuration Utility

over USB or Wi-Fi

Telnet console over Wi-Fi

Terminal menu over RS-232

CS I/O Port

SDC 7, 8, 10, 11 (does not support ME)

9600 to 460.8 kbps

RS-232 Port

DTE

1200 bps to 115.2 kbps

WLAN

Antenna Connector: RP-SMA

Supported Technologies: 802.11b/g/n, WPA/WPA2-Personal, WPA/WPA2-Enterprise Security,
WEP

Client Mode: WPA/WPA2-Personal and Enterprise, WEP

Access Point Mode: WPA2-Personal

NL241 Wireless Network Link Interface

Summary of Contents for NL241












































































Search results

Summary of Contents for NL241

Reviews:

Related manuals for NL241

Brands by name

Popular brands

Campbell NL241, Product Manual

Search results

Summary of Contents for NL241

Reviews:

Related manuals for NL241

Brands by name

Popular brands