background image

1/2 inch Impact 

Wrench

Table of Contents

Description   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1
Unpacking  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1
Safety Guidelines   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  1
Important Safety Information  .  .  .  .  .  .  1
Tool Components and  
Specifications .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  2
Operating Instructions  .  .  .  .  .  .  .  .  .  .  .  .  4
   Lubrication  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4
   Recommended Hookup .  .  .  .  .  .  .  .  .  .  4
   Operational Mode  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4
User-Maintenance Instructions   .  .  .  .  .  5
Troubleshooting Charts   .  .  .  .  .  .  6 and 7
Warranty  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  8

Description

This is a rocking dog type impact 
wrench designed for DIY projects and 
general purpose applications such as 
maintenance, car repair, and lawn and 
garden equipment . Not intended for 
assembly line

 applications or heavy duty 

usage .

Unpacking

After unpacking the unit, inspect 
carefully for any damage that may 
have occurred during transit . Make sure 
to tighten fittings, bolts, etc ., before 
putting unit into service .

CalIfornIa proposITIon 65

 

This product or 

  its power cord may 

contain chemicals known to the State 
of California to cause cancer and birth 
defects or other reproductive harm. 
Wash hands after handling.

You can create dust when 
you cut, sand, drill or grind 
materials such as wood, 
paint, metal, concrete, cement, or other 
masonry. This dust often contains 
chemicals known to cause cancer, birth 
defects, or other reproductive harm. 
Wear protective gear.

safety Guidelines

This manual contains information 
that is very important to know and 
understand . This information is 
provided for SAFETY and to PREVENT 
EQUIPMENT PROBLEMS . To help 
recognize this information, observe the 
following symbols .

 

Danger indicates an  

  imminently 

hazardous situation which, if not 
avoided, WILL result in death or serious 
injury.
 

Warning indicates a  

  potentially 

hazardous situation which, if not 
avoided, COULD result in death or 
serious injury.
 

Caution indicates a   

  potentially 

hazardous situation which, if not 
avoided, MAY result in minor or 
moderate injury.
 

Notice indicates  

  important 

information, that if not followed, may 
cause damage to equipment.

noTE:

 Information that requires special 

attention .

Important safety Instructions

InsTrUCTIons pErTaInInG To a 
rIsK of fIrE, ElECTrIC sHoCK, or 
InJUrY To pErsons 

This manual contains safety, operational 
and maintenance information . Contact 
your Campbell Hausfeld representative 
if you have any questions .

 

When using tools,  

  basic precautions 

should always be followed, including 
the following:

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. 
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or 
property damage! Retain instructions for future reference.

REMINDER: Keep your dated proof of purchase for warranty purposes! 

Attach it to this manual or file it for safekeeping.

IN732800AV 1/10

see Warranty on page 8 for important information about commercial use of this product.

operating Instructions   

Tl0502

Locate model and date code on 

tool and record below:
Model No .: _____________________
Date Code: _____________________

Retain these numbers for 

future reference .

© 2010 Campbell Hausfeld / Scott Fetzer

For parts, product & service information 

visit 

www.chpower.com

Model Tl0502

Summary of Contents for TL0502

























Reviews: