![background image](http://html1.mh-extra.com/html/cadac/b-type/b-type_installation-and-user-manual_3239265093.webp)
Grand Master Group module 7795
7-7
Revision B2005-2
B-Type
:14158
$X[
#
*URXS
#
$
#
WR
#
/LVWHQ
#
0RGXOH
Press this switch to ’monitor’ the signal in the Aux Group via the Listen module. The
signal source and monitor destination is set by the switches mounted directly below:
“FROM”
Pre or post INSERT
Pre or post Fader
“TO LISTEN”
L2 (always mono)
L1 in mono
L1 in stereo
:14159
$X[
#
*URXS
#
%
#
WR
#
/LVWHQ
#
0RGXOH
As above for Aux Group B.
:1415:
$X[
#
*URXS
#
WR
#
/LVWHQ
#5
Press this switch to monitor the Aux Groups on the L2 section of the Listen Module.
This is one of three ‘pre-set’ monitor destination switches, so you will not “hear” any-
thing until you press one of the “Aux Group to Listen Module” switches. Note that L2
is always in mono.
:1415;
$X[
#
*URXS
#
WR
#
/LVWHQ
#4#+
LQ
#
PRQR
,
Press this switch to monitor the Aux Groups on the L1 section of the Listen Module in
mono. This is one of three ‘pre-set’ monitor destination switches, so you will not
“hear” anything until you press one of the ‘Aux Group to Listen Module” switches.
Note that L1 is a stereo monitoring circuit, so if the “Aux Group A to Listen” switch is
pressed, the signal from Aux Group A is only routed to the L1 left output. Similarly, if
“Aux Group B to Listen” switch is pressed, the signal from Aux Group B is only
routed to the L1 right output.
:1415<
$X[
#
*URXS
#
WR
#
/LVWHQ
#4#
6WHUHR
Press this switch to monitor the Aux Groups on the L1 section of the Listen Module in
stereo. This is one of three ‘pre-set’ monitor destination switches, so you will not
“hear” anything until you press one of the “Aux Group to Listen Module” switches.
Note that L1 is a stereo monitoring circuit, so if the “Aux Group A to Listen” switch is
pressed, the signal from Aux Group A is only routed to the L1 left output. Similarly, if
“Aux Group B to Listen” switch is pressed, the signal from Aux Group B is only routed
to the L1 right output.
:14163
0RQLWRU
#
$X[
#
*URXS
#
35(
#
RU
#
3267
#
,16(57
One of two ‘source’ selection switches, the default monitor condition for the Aux
Groups is POST INSERT, POST FADER (both “FROM” switches not selected).
Press the “PRE INS” switch to change the Aux Group’s monitor point to ‘pre-insert’.
:14164
0RQLWRU
#
$X[
#
*URXS
#
35(
#
RU
#
3267
#
)DGHU
One of two ‘source’ selection switches, the default monitor condition for the Aux
Groups is POST INSERT, POST FADER (both “FROM” switches not selected).
Press the “PRE FAD” switch to change the Aux Group’s monitor point to ‘pre-fader’.
:14165
'
1
&
1#
'LVSOD\
#+
SURJUDPPDEOH
,
An alpha-numeric display that allows up to eight characters to be programmed on the
PC and sent to the fader display with the rest of the cue information. It is possible to
send different information for each cue in the show.
Summary of Contents for B-Type
