CAB SQUIX Configuration Manual Download Page 47

Page: 47 / 64

I/O Interface

Pin

Signal Name

Description

Activation / Active State

PEELPOS

Label in peel-off position
For peel-off mode only.

A label is in peel-off position.

+24 V on Pin 21

Bit 3

User Bit 3 is set

ERROR

General error message
The operation will be stopped and the error type will be
displayed.

0 V on Pin 22

STOP

Stop signal to interrupt the operation

Switch on +24 V between
Pin 23 and Pin 25

Do not use

GND_EXT

Ground of the external 24 V

Table 29

Pin assignment of the I/O interface

12.2 Circuit Diagram of Inputs and Outputs

Digital Inputs

•

conform to IEC/EN 61131-2 (Type 3)

•

Operating voltage: 24 V DC (9,6..35 V)

•

Switching logic: PNP switching

•

Low level „0“: < 7 V DC

•

High level „1“: > 11 V DC

•

Input current per channel: 1,5..2,5 mA (at 24 V DC)

•

Reverse polarity protection: yes

•

ESD protection: conform to IEC/EN 6100-4-4

Digital Outputs

•

conform to IEC/EN 61131-2

•

Operating voltage: 24 V DC (11..35 V)

•

Switching logic: PNP switching

•

Output current per channel: 625 mA
(overload protection)

•

Short-circuit protection: yes

•

Reverse polarity protection: yes

•

ESD protection: conform to IEC/EN 6100-4-4

Pin 20

P24_EXT

Pin 1

Pin 12

REPRINT

Pin 13

START

Pin 14

PAUSE

Pin 16

LBLREM

Pin 17

JOBDEL

Pin 18

RSTERR

Pin 23

STOP

Pin 25

GND_EXT

Pin 20

P24_EXT

Pin 3

Pin 4

FEEDON

Pin 5

Pin 9

JOBRDY

Pin 10

READY

Pin 15

RIBWARN

Pin 21

PEELPOS

Pin 22

ERROR

Pin 25

GND_EXT

Figure 26

Connecting inputs

Figure 27

Connecting outputs

Summary of Contents for SQUIX

































































Search results

Summary of Contents for SQUIX

Reviews:

Brands by name

Popular brands

CAB SQUIX, Configuration Manual

Search results

Summary of Contents for SQUIX

Reviews:

Brands by name

Popular brands