BYD S6 Owner'S Manual Download Page 76

Page: 76 / 139

BYD AUTO S6, S6A, S6K Owner's Manual

Comfort and convenience devices 1-71

km/h.

c. Press the deceleration/set (-/SET)

button to initiate the cruise control.

．

The cruise control cannot maintain

the set speed when the car is going

up or down a slope.

Changing a set speed

The preset cruise speed can be raised

with any of the following methods:

a. The car can be accelerated

continuously by holding the

acceleration/reset (+/RES) button.

When the expected cruise speed is

reached, simply release the button.

b. Depress the accelerator pedal.

Press the deceleration/set (-/SET)

button after the expected cruise

speed is reached.

c. If you want to raise the speed

slightly, you can press the

acceleration/reset (+/RES) button

repeatedly. The speed will increase

by 1.6 km/h for each press.

The preset cruise speed can be reduced

with any of the following methods.

a. The car can be decelerated by

holding the deceleration/set (-/SET)

button. When the expected cruise

speed is reached, simply release

the button.

b. Depress the brake pedal lightly.

When the car is decelerated to the

expected speed (over 40 km/h),

press the deceleration/set (-/SET)

button. The car will maintain the

expected speed.

c. If you want to reduce the speed

slightly, you can press the

deceleration/set (-/SET) button

repeatedly. The speed will decrease

by 1.6 km/h for each press.

Canceling cruise control

Cruise control can be cancelled with

any of the following methods:

a. Depress the brake pedal.

b. Press the cancel (CANCEL) button

on the steering wheel.

c. Press the master cruise control

button (ON/OFF).

d. Exit from gear D.

Auxiliary Parking System (optional)

WARNING



When the speed is over 10 km/h,

the auxiliary parking system will

stop working.



Do not add any other object

within the working range of the

sensor.



Do not wash the sensor with

water or steam. Otherwise, the

Summary of Contents for S6












































































































































Search results

Summary of Contents for S6

Reviews:

Related manuals for S6

Brands by name

Popular brands

BYD S6, Owner'S Manual

Search results

Summary of Contents for S6

Reviews:

Related manuals for S6

Brands by name

Popular brands