BYD S6 Owner'S Manual Download Page 59

Page: 59 / 139

BYD AUTO S6, S6A, S6K Owner's Manual

Instruments and Indicator Lights 1-54

used to indicate the user to faults with

the car. In this case, you have to

contact the BYD auto sales service

station for repair.

Display

description or

buzzer tone

Description

Cooling fluid

temperature

is over high

This information will

be displayed when the

cooling fluid

temperature is above

high. Stop the car

immediately and

contact BYD auto

sales service station.

Low engine

oil pressure

The engine oil is not

sufficient. Stop driving

and contact the BYD

auto sales service

station immediately.

Check

charging

This information

indicates that there is

system

fault with the charging

system. Stop the car

immediately and

contact the BYD auto

sales service station.

Check brake

system

This information

indicates that the

brake fluid level is low

or there is a fault with

the braking system.

Stop the car

immediately and

contact the BYD auto

sales service station.

Check the

ABS system

This information will be

displayed when there

is fault with the ABS or

braking system.

Contact the BYD auto

sales service station

for inspection

immediately.

Check the

The information will be

SRS system

displayed when faults

are found with the

SRS. Contact the

BYD auto sales

service station for

inspection

immediately.

Please

inspect the

vehicle

network

This information will

be displayed when the

vehicle network is

abnormal. Stop the

car immediately and

contact the BYD auto

sales service station.

Indicator for Unfastened Front

Passenger Seat Belt

The driver seat belt prompt system

works via the indicator light and the

buzzer and is used to remind the

driver and the passenger to fasten the

seat belts.

Summary of Contents for S6












































































































































Search results

Summary of Contents for S6

Reviews:

Related manuals for S6

Brands by name

Popular brands

BYD S6, Owner'S Manual

Search results

Summary of Contents for S6

Reviews:

Related manuals for S6

Brands by name

Popular brands