BWT Perla Hybrid Installation And Operating Manual Download Page 23

Page: 23 / 84

Start screen

►

Press

CONTINUE

8 2

Installation check

The installation check verifies that your product is

properly connected.

►

Press

START CHECK

to begin.

Installation check 1/4: Waste water connection

according to EN1717

►

Check that the waste water hoses are connected

properly (see chapter

“6.2.1 Establishing a sew

age system connection”, page

18).

If all criteria for correct installation are satisfied:

►

Press

INSTALLED

Installation check 2/4: Ports on the connection

fitting

►Ensure that the hoses for the inflow and outlet

water at the connection fitting are correctly con

nected (see chapter

“6.2 Connecting the product”,

page 17).

►

Open the connection fitting by turning the

handwheel anti-clockwise until it stops. Rinsing

of the product starts.

If all criteria for correct installation are satisfied:

►

Press

INSTALLED

Summary of Contents for Perla Hybrid





















































































Search results

Summary of Contents for Perla Hybrid

Reviews:

Brands by name

Popular brands

BWT Perla Hybrid, Installation And Operating Manual

Search results

Summary of Contents for Perla Hybrid

Reviews:

Brands by name

Popular brands