BUSCH MINK ATEX MM 1102 BVE Instruction Manual Download Page 34

Page: 34 / 40

10 | Spare Parts

34 | 40

Instruction Manual MINK MM 1104-1142 BV ATEX_EN_en

Spare Parts

NOTICE

Use of non-Busch genuine spare parts.
Risk of premature failure!
Loss of efficiency and ATEX compliance!

●

The exclusive use of Busch genuine spare parts and consumables is recommended for the correct
functioning of the machine and to validate the warranty.

Spare part

Description

Part no.

Oil fill plug (=Venting valve)

Includes appropriate seal ring

0543 107 407

Oil sight glass (OSG)

0583 000 001

Seal ring

For oil sight glass (OSG)

0480 000 271

Oil drain plug (ODP)

Includes appropriate seal ring

0415 134 870

Seal ring

For oil drain plug (ODP)

0482 137 352

Inlet flange lower part

Includes non-return valve (NRV)

0916 102 518

Inlet screen (IS)

0534 000 018

ATEX inlet filter

paper

0530 232 509

ATEX inlet filter

polyester

0530 232 513

ATEX inlet filter cartridge

paper

0532 232 507

ATEX inlet filter cartridge

polyester

0532 232 508

If other parts are required:

●

Contact your Busch representative.

Summary of Contents for MINK ATEX MM 1102 BVE









































Search results

Summary of Contents for MINK ATEX MM 1102 BVE

Reviews:

Related manuals for MINK ATEX MM 1102 BVE

Brands by name

Popular brands

BUSCH MINK ATEX MM 1102 BVE, Instruction Manual

Search results

Summary of Contents for MINK ATEX MM 1102 BVE

Reviews:

Related manuals for MINK ATEX MM 1102 BVE

Brands by name

Popular brands