Transportation
The vacuum systems COBRA DS are tested and checked in our factory
before carefull packing. Check the packaging for transport damage
when the goods arrive. The vacuum system can withstand tempera-
tures between –25°C and +55°C during transport.
Handling
For handling of individual components look up the relevant Operating
Instructions in the Appendix.
The vacuum system is supplied in wooden crates.
The ring bolts on the components are not designed to take the full
weight of the vacuum system.
Depending on the dead weight and size of the vacuum system, use a
forklift to move it on several pallets.
Or lift the vacuum system usings slings and the appropriate lifting gear
to move the vacuum system or remove the pallets.
Be sure to avoid strain on pipework or vacuum pumps when placing
the slings.
Transportation in packed state
The vacuum system is packed in wooden crates. it protects the vacuum
system from damage in transit.
Transportation in unpacked state
The vacuum system can be transported without the wooden crates
with a lift truck or using slings and appropriate lifting gear which will
take the full weight of the vacuum system.
CAUTION
Do not work, walk or stand under suspended loads.
CAUTION
Please check out the weight of the vacuum pump before lifting it up
(see "Technical Data").
Use adequate lifting gear for this.
NOTE
: The suspension eyes are located at about the center-of-gravity
of the vacuum pumps. If the vacuum pumps are equipped with acces-
sories that could influence the center-of-gravity, this must be taken
into account when lifting and a belt must additionally be attached to a
specific point.
Lifting for DP 0600 C
l
Fasten the hoist to the suspension eyes on the cylinder
l
Use a hoist that is equipped with a hook and safety lock
l
Lift the vacuum pump
If the vacuum pump is fastened to several pallets with fixing pins:
u
Unscrew the fixing pins in the base frame
CAUTION
In the case of a vacuum system filled with oil, you ensure that the
angle of inclination of the vacuum system at the time of rise does
not exceed 5° compared to the horizontal. In the event of too im-
portant slope (> 5°), risk of oil leakage in the workspace.
Before each transport requiring a means of adapted lifting, control the
slope of the vacuum system (< 5°).
The packaging material must be disposed of in accordance with local
and national regulations.
This handbook is contained in the delivery package.
For future transportation :
l
Seal all open connections with protective caps (to prevent penetra-
tion of dirt and water)
l
Secure loose cables
l
Protect from shock
l
Drain all process and operating media
l
Secure vacuum system firmly before transporting (e.g. bolt to
several pallets)
l
Use a lift truck to move and set the vacuum system down
Storage
Take the following precautions before putting the vacuum system into
storage:
l
Clean and dry the vacuum system
l
Where necessary use oil for conservation
l
Before storing make absolutely sure that all parts are clean, drained
and dry
See relevant documentation in the appendix for precise instructions on
individual vacuum system components
Removal of the vacuum system
Before starting a vacuum system that has been stored outside the
building for a while, the vacuum system must be moved to a room
with ambient temperature, where it should rest for a day.
Preservation
If the vacuum system will be exposed to unfavourable ambient condi-
tions (for example, aggressive environment, frequent temperature
changes), begin immediately with preservation work on the vacuum
system.
In the case of favourable ambient conditions, perform preservation
work on the vacuum system if a storage period of more than three
months is planned.
l
Make sure that all openings are hermetically sealed; use adhesive
tape to fasten loose parts (seal rings, flat seals, etc.).
NOTE
: VCI is the abbreviation for “volatile corrosion inhibitor”. The
VCI molecule is an organic corrosion inhibitor in the vapour phase. In-
tegrated in various carriers such as film, cardboard, paper, foam, liquid
and powder, it protects the parts against corrosion as a result of its
action in the vapour phase. However, VCI packaging can attack syn-
thetic surfaces and surfaces of other elastomers. If in doubt, please
contact your nearest distributor. VCI packaging provides several years
of protection against corrosion, even under the harshest of conditions:
overseas shipment, extended storage before use.
l
Wrap the vacuum system in a VCI film
l
Store the vacuum system
–
if possible, the vacuum system should be stored in its original
packaging,
–
indoors,
COBRA DS 8163 A
Transportation
0870772605
Page 15
Summary of Contents for COBRA DS 8163 A
Page 34: ......
