manualshive.com logo in svg

Bunn ingle Multi- BrewWISEDBC WITH SMART FUNNELTM, Installation And Operating Manual, Page: 38 / 50

Share
Download
Bunn ingle Multi- BrewWISEDBC WITH SMART FUNNELTM Installation And Operating Manual Download Page 38

Page 38

FACTORY DEFAULTS

This function allows the operator to erase 

all

 of the

previously entered recipes and ad messages. Factory-
set default values will replace 

all

 previous settings.

Procedure to set factory defaults:

1. Press and hold the ® pad until 

WARMER OFF

appears. Release the ® pad.  Press and release ®
until the display reads 

FACTORY DEFAULTS

.

2. Pressing 

NO

 in this screen will revert to the 

MAIN

SCREEN

.  Press 

YES

 to replace the defaults.  This

advances to 

WILL REPLACE ALL BREWING SET-

TINGS

.  This screen will alternate with 

ARE YOU

SURE?

.

3. Pressing 

NO

 in the confirmation screen will revert

to 

MAIN SCREEN

, without resetting the brewing

setups to the defaults. Press 

YES

 to load the

defaults. This will then revert to the 

MAIN SCREEN

,

and the factory default values will replace 

all

previously entered values. It will NOT reset the
summation Brew counter.

P2312

PROGRAMMING FUNCTIONS - LEVEL 2 (cont.)

FACTORY DEFAULT VALUES

Brew Lockout

NO

DEFAULT (NO NAME) SETTINGS:

Iced Coffee

BREW VOLUME

1800 mL

DILUTION VOLUME

0 mL

PULSE BREW TIME

None

PREINFUSION TIME

1st 0:53,OFF 0:45

DRIP OUT TIME

1:00

Hot Coffee

Half Batch

Full Batch

BREW VOLUMES

900 mL

1800 mL

DILUTION VOLUMES

0 mL

0 mL

PULSE BREW TIMES

None

None

PREINFUSION TIMES

1st 0:15,Off 1:00

None

DRIP OUT TIMES

0:30

0:45

Iced Tea

BREW VOLUMES

2800 mL

DILUTION PERCENTAGE

53%

PULSE BREW TIMES

None

PREINFUSION TIMES

None

DRIP OUT TIMES

0:45

ENABLE ADS

YES

BREW TEMPERATURE

93˚C (200˚F)

READY TEMPERATURE

91˚C (195˚F)

REFILL

155

SPRAY (Ml/MINUTE)

1160

DILUTE (Ml/MINUTE)

730

FUNNEL LOCKOUT

NO

UNITS

METRIC

37467  110904

Summary of Contents for ingle Multi- BrewWISEDBC WITH SMART FUNNELTM



















































Reviews:

No comments