manualshive.com logo in svg

Bulls Lacuba EVO 45 Sport, Original Operating Instructions, Page: 94 / 133

Share
Download
Bulls Lacuba EVO 45 Sport Original Operating Instructions Download Page 94

Maintenance

MY19B103_1.0_04.01.2019

94

8.1.2.4

Cleaning the drive elements

Spray the cassette, the chain wheels and the front 
derailleur with a degreasing agent.

Clean coarse dirt with a brush after soaking for a 
short time.

Wash down all parts with dish-washing detergent 
and a toothbrush.

Service the drive elements after cleaning.

8.1.2.5

Cleaning the chain

Slightly dampen a brush with dish-washing liquid. 
Brush both sides of the chain.

Dampen a cloth with dish-washing liquid. Place the 
cloth on the chain.

Hold with slight pressure while slowly turning the 
rear wheel, so the chain passes through the cloth.

If the chain is still dirty afterwards, clean it with 
WD40.

Service the chain after cleaning.

Never use aggressive (acid-based) cleaners, rust 
removers or degreasers when cleaning the chain.

Do not use chain cleaning devices or chain cleaning 
baths.

NOTICE

EN_MY19B103_1.0_BULLS Brose Lacuba Evo 45 Sport MY19_Inhalt.book  Page 94  Tuesday, January 8, 2019  4:38 PM

Summary of Contents for Lacuba EVO 45 Sport






































































































































Reviews:

No comments