manualshive.com logo in svg

Bulls Lacuba EVO 45 Sport, Original Operating Instructions, Page: 85 / 133

Share
Download
Bulls Lacuba EVO 45 Sport Original Operating Instructions Download Page 85

MY19B103_1.0_04.01.2019

85

Operation

7.9

Brake 

  

Hydraulic fluid can be fatal if it is swallowed and 
penetrates into the respiratory system

Hydraulic fluid may leak out after an accident or due to 
material fatigue. Hydraulic fluid can be fatal if 
swallowed and inhaled.

First aid treatment

Wear gloves and safety goggles as protective 
equipment. Keep unprotected persons away.

Remove those affected from the danger area to 
fresh air. Never leave those affected unattended.

Ensure sufficient ventilation.

Immediately remove clothing items contaminated 
with hydraulic fluid.

Serious slip hazard due to hydraulic fluid leakage.

Keep away from naked flames, hot surfaces and 
sources of ignition.

Avoid contact with skin and eyes.

Do not inhale vapours or aerosols.

After inhalation

Take in fresh air; consult doctor if any pain or 
discomfort.

After skin contact 

Wash affected skin with soap and water and rinse 
well. Remove contaminated clothing. Consult 
doctor if any pain or discomfort.

DANGER

!

EN_MY19B103_1.0_BULLS Brose Lacuba Evo 45 Sport MY19_Inhalt.book  Page 85  Tuesday, January 8, 2019  4:38 PM

Summary of Contents for Lacuba EVO 45 Sport






































































































































Reviews:

No comments