Home
/
Bull
/
DPS7000/XTANOVASCALE 7000 180Rb 7
/
Service Manual

Bull DPS7000/XTANOVASCALE 7000 180Rb 7, Service Manual, Page: 88 / 258

Share

Page: 88 / 258

Bull DPS7000/XTANOVASCALE 7000 180Rb 7 Service Manual Download Page 88

3-28

Configuring Your System

Figure 3-2 shows the SEL viewer main window. Table 3-4 lists the window’s
menus and options.

Figure 3-2. SEL Viewer Add-in Main Window

Table 3-4.

SEL Viewer Menus

Menu

Options

File

Open SEL: Views data from previously saved SEL file.
Save SEL: Saves the currently loaded SEL data to a file.
Clear SEL: Clears the SEL data from the BMC.
Exit: Quits the SEL Viewer.

View

SEL Info: Displays information about the SEL (display only).
All Events: Displays the current SEL data from the BMC.
By Sensor: Displays a pop-up menu allowing you to view the data from a certain sensor type.
By Event: Displays a pop-up menu allowing you to view the data from a certain event type.
Monitor Real-time: Displays SEL information in real time, allowing you to continuously monitor the
SEL (events are displayed as soon as they are posted to the SEL).

Settings

Display Hex/Verbose: Toggles between hex/interpreted mode of displaying the SEL records.
Output Text/Binary: Determines whether SEL data will be saved to the file (and under File\Save)
in binary format or verbose format.

Help

About: Displays the SEL Viewer version information.

«
...
86
87
88
89
90
...
»

Summary of Contents for DPS7000/XTANOVASCALE 7000 180Rb 7



































































































































































































































































Reviews:

No comments