manualshive.com logo in svg

Bull DPS7000/XTANOVASCALE 7000 180Rb 7, Service Manual, Page: 77 / 258

Share
Download
Bull DPS7000/XTANOVASCALE 7000 180Rb 7 Service Manual Download Page 77

Configuring Your System   3-17

Exit Menu

The following menu options are available on the Server menu.  Select an option
by using the up or down arrow keys.  Then press <Enter> to execute the option,
and follow the prompts.

Option

Description

Exit Saving Changes

Exit Setup and save your changes to CMOS.

Exit Discarding Changes

Exit Setup without saving data to CMOS.

Load Setup Defaults

Load default values for all Setup items.

Load Custom Defaults

Load settings from custom defaults.

Save Custom Defaults

Save changes to custom defaults.  Normally PhoenixBios reads setup settings
from CMOS.  However, if CMOS fails, BIOS  uses custom defaults—if you
have set them.  If not, BIOS uses factory defaults.

Discard Changes

Load previous values from CMOS for all Setup items.

Save Changes

Save Setup data to CMOS.

Summary of Contents for DPS7000/XTANOVASCALE 7000 180Rb 7



































































































































































































































































Reviews:

No comments