Buhler SCS 104 Installation And Operation Instructions Manual Download Page 11 | Manualshive

Page: 11 / 75

background image

SCS 104

CAUTION

Supply cable

The power adapter must be suitable for the maximum power input of the device. It must
be heat-resistant and must not come into contact with hot surfaces. The power adapter
must meet IEC60227 or IEC60245. Or be approved by another recognised testing body.

Run the lines so the insulation will not be damaged. If necessary, secure the lines with suitable means and avoid excess line
lengths.

The power and voltage supply must be equipped with ELCB.

The ELCB (tripping current 30 mA) must shut off the load within the specified period (200 ms at 115 VAC, 40 ms at 230 VAC). It
must be suitable for the maximum load.

9

Bühler Technologies GmbH

BECS0031 ◦ 02/2020

«
...
9
10
11
12
13
...
»

Summary of Contents for SCS 104












































































Reviews:

No comments

Related manuals for SCS 104

Brand: TaiDoc Pages: 31

Brand: A&D Pages: 74

Brand: ABQ Industrial Pages: 15

Brand: ABQINDUSTRIAL Pages: 3

Brand: Galileo Pages: 19

Brand: Galileo Pages: 71

Brand: Unico Pages: 96

Brand: jablotron Pages: 2

Brand: NCTE Pages: 10

Brand: Veeder-Root Pages: 39

Brand: Veeder-Root Pages: 98

Brand: VECTECH Pages: 9

Brand: Facom Pages: 48

Brand: Hanna Instruments Pages: 9

Instrument Control System

Brand: Opus-Two Pages: 8

Brand: YATO Pages: 36

Brand: Clavitech Pages: 56

Brand: SANKO Pages: 97

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands