manualshive.com logo in svg

Buderus Logamatic EMS RC35, Installation And Service Instructions Manual

Share
Download
Buderus Logamatic EMS RC35 Installation And Service Instructions Manual Download Page 38

System settings (Service menu – Settings)

Logamatic EMS RC35 programming unit - Subject to technical modifications

38

6

 

Should the LED of the single 
charge key be activated?

yes, no

yes

The heating once only function 
is retained, but is no longer 
indicated by the LED.

5)

Start delay for preheated 
DHW (e.g. solar):

OFF, 
1 sec. to 50 sec.

OFF

This function depends on the 
boiler used.

1) Not possible or available on boilers with UBA1.x, UBA-H3 or DBA.

2) Not possible or available on boilers with UBA1.x or DBA.

3) On boilers with UBA-H3 subject to the availability of the PZ output (e.g. with module LM10).

4) Subject to the boiler in use, the temperature is permanently fixed an cannot be modified.

5) Not possible or available on boilers with UBA1.x.

Menu item

Input range

Factory 
setting

Other information

Tab. 14 Navigator for service menu SETTINGS\DHW

Summary of Contents for Logamatic EMS RC35





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands