manualshive.com logo in svg

Buderus Logamatic EMS RC35, Installation And Service Instructions Manual

Share
Download
Buderus Logamatic EMS RC35 Installation And Service Instructions Manual Download Page 10

Installation

Logamatic EMS RC35 programming unit - Subject to technical modifications

10

3

 

3

Installation

3.1

Choosing the right installation position

3.1.1 Installation in reference room 

If the system is room-temperature controlled, the following requirements must be observed:

• Installation position on an internal wall (

Æ

 Fig. 1)

• Maintain the specified distance from the door (to avoid draughts).

• Allow clearance below the programming unit (

Æ

 Fig. 1, shaded area) (to ensure correct 

temperature measurement).

• The reference room (= installation room) must be as representative as possible of the entire 

home. External heat sources in the reference room (e.g. sunlight or other heat sources such as 
an open fire) affect the control functions. This means it may be too cold in rooms without external 
heat sources.

• Always open the thermostatic radiator valves fully in the reference room to prevent the two 

temperature controllers influencing each other.

Fig. 1

Minimum clearances for installation in a reference room

If there is no suitable reference room, we recommend setting the system to weather-
compensated control instead (this requires an outside temperature sensor). 
Alternatively, you could install an external room temperature sensor in the room with the 
greatest heating requirements (e.g. living room).

6 720 618 477-01.1RS

Summary of Contents for Logamatic EMS RC35





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands