manualshive.com logo in svg

Buderus Logamatic EMS RC35, Installation And Service Instructions Manual

Share
Download
Buderus Logamatic EMS RC35 Installation And Service Instructions Manual Download Page 11

Logamatic EMS RC35 programming unit - Subject to technical modifications

11

Installation

3

 

3.1.2 Installation on boiler

Installation directly on the boiler is possible where the boiler is equipped with the Energy 
Management System (EMS).

The outside temperature sensor for weather-compensated control is not delivered as standard, but 
can be ordered as an accessory.

3.2

Types of installation

The programming unit can be installed in three different ways:

• As only programming unit in the system (factory setting): the programming unit is installed in the 

living space (reference room) or on the boiler. 
Example: detached house with one heating circuit.

• As the only programming unit in a heating system with two or more heating circuits

1)

 (

Æ

Fig. 2 

[1]).
Examples: underfloor heating on one floor, radiators on the others; or a main flat together with a 
separate granny flat or doctor's surgery.

• In conjunction with a remote control (e.g. RC2x, RC20/RF, Fig. 2, [2]). In this case there are 

always two separate heating circuits. Remote control units cannot be used for boilers with 
UBA1.x.
Examples: underfloor heating on one floor, radiators on the others; or a main flat together with a 
separate granny flat or doctor's surgery.

Fig. 2

Options for a heating system with two heating circuits

1

Both heating circuits are controlled by one programming unit.

2

Each heating circuit has its own programming unit / remote control unit.

1) Not possible with boilers with UBA1.x and DBA.

6 720 641 642-01.1RS

2

1

HC1

HC1

HC2

HC2

Summary of Contents for Logamatic EMS RC35





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands