manualshive.com logo in svg

Buderus Logamatic EMS RC35, Installation And Service Instructions Manual

Share
Download
Buderus Logamatic EMS RC35 Installation And Service Instructions Manual Download Page 37

Logamatic EMS RC35 programming unit - Subject to technical modifications

37

System settings (Service menu – Settings)

6

 

DHW circulation

2)3)

Is a circulation pump 
installed?

yes, no

no

How frequently should 
the circul. pump be 
switched on per hour?

once for 3 minutes, 
twice for 3 minutes, 
3 times for 3 minutes, 
4 times for 3 minutes, 
5 times for 3 minutes, 
6 times for 3 minutes, 
permanent operation

Twice for 
3 minutes

switch on circ. pump

Graphical display of number of 
times the pump is switched on 
per hour. 

Do you wish to change 
the circulation switching 
programme?

yes, no

no

When selecting “yes” the 
system jumps to the DHW 
circulation switching program.

Thermal disinfection

2)

Should a thermal 
disinfection be carried 
out?

yes, no

no

What temperature should 
be used for thermal 
disinfection?

60 °C to 80 °C

4)

70 °C

At temperatures above 60 °C 
there is a risk of scalding at the 
draw-off points during and after 
thermal disinfection!
 

On which day should the 
thermal disinfection be 
performed?

Monday, Tuesday, 
Wednesday, 
Thursday, Friday, 
Saturday, Sunday, 
daily

Tuesday

At what time of day 
should the th. disinfection 
be performed?

0:00h to 23:00h

1:00h

Times entered must be whole 
hours only (no minutes).

Menu item

Input range

Factory 
setting

Other information

Tab. 14 Navigator for service menu SETTINGS\DHW

Summary of Contents for Logamatic EMS RC35





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands