btsr ULTRAFEEDER Operating Manual Download Page 34

Page: 34 / 81

Technical Data and Installation

- 2.22 -

ULTRAFEEDER

Connect the KTF10/FIX cable

to the KTF/FIX connector

Connect the KTF10/FIX cable to the 8 pin connector of
ULTRAFEEDER

In case of Master/Slave connection, the KTF10/FIX cable
must be connected to the MA8/15/FE10/CAN cable male
connector, which is connected in turn to the
ULTRAFEEDER device 10 pin connector (without adapter
cap)
See picture on page 2.23.

ULTRAFEEDER correctly connected to the flat cable through
KTF/FIX clamping bracket

The flat cable support bar must have a height of 25 mm.

Connection cables and accessories in case of installation with flat cable KTF/FLAT

Flat cable KTF/FLAT for KTF/FIX

KTF/FLAT Variable

length

Flat cable KTF/FLAT for KTF/FIX with connectors for BX4030RTP-X4

power supply module connection

500/FLAT/PW4

Length 500 cm, with connector for KTF/PW4

Connection cable between ULTRAFEEDER and KTF/FIX

KTF10/FIX

Length 10 cm

Quick multi-connection clamping of ULTRAFEEDER with flat cable

KTF/FLAT

KTF/FIX

Insulation pass-through rapid clamping bracket

Summary of Contents for ULTRAFEEDER


















































































Search results

Summary of Contents for ULTRAFEEDER

Reviews:

Related manuals for ULTRAFEEDER

Brands by name

Popular brands

btsr ULTRAFEEDER, Operating Manual

Search results

Summary of Contents for ULTRAFEEDER

Reviews:

Related manuals for ULTRAFEEDER

Brands by name

Popular brands