btsr ULTRAFEEDER Operating Manual Download Page 27 | Manualshive

Page: 27 / 81

background image

Technical Data and Installation

ULTRAFEEDER

- 2.15 -

PFU/64FS –Software Mode

This mode allows you to entirely manage the yarn feeding devices connected via serial communication line.
This configuration is intended for system integrators and applications using the PC LINK BTSR program
family.

The functions available by means of the different machine interface connectors are described in detail below.
For the Pin assignment, please refer to paragraph “

PFU/64FS power supplier electrical interface

” on page

2.10.

SMART connector

This connector makes available 2 serial lines:

SMART RxTx+
SMART RxTx-

Serial line reserved for SMART MATRIX PFU terminal connection (communication
speed 345600

Bps)

AUX RxTx+
AUX RxTx-

Serial line reserved for communication with PC LINK BTSR software
(communication speed 115200 Bps)

SMART-IN

«
...
25
26
27
28
29
...
»

Summary of Contents for ULTRAFEEDER


















































































Reviews:

No comments

Related manuals for ULTRAFEEDER

Brand: Paratec Pages: 8

Brand: J+J Pages: 33

Brand: Watts Pages: 2

Brand: Hanbay Pages: 18

Brand: Campbell Pages: 72

Brand: Gardena Pages: 18

VLT Micro Drive FC 51 Series

Brand: Danfoss Pages: 23

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 6

EIP-2000 Series

Brand: ICP DAS USA Pages: 19

Brand: ICP DAS USA Pages: 4

Brand: Jedia Pages: 12

Brand: JED Micro Pages: 10

Brand: JCM Technologies Pages: 2

Brand: KaRo Pages: 12

Brand: VENCO Pages: 44

Brand: Wabtec Pages: 106

Brand: Daihan Scientific Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands