Bryant 580J Series Installation Instructions Manual Download Page 34

Page: 34 / 52

COVER REMOVED

SIDE VIEW

C07135

Fig. 48 -- Outdoor Air Quality Sensor Cover

Wiring the Outdoor Air CO

Sensor:

A dedicated

power supply is required for this sensor. A two--wire cable

is required to wire the dedicated power supply for the

sensor. The two wires should be connected to the power

supply and terminals 1 and 2.

To connect the sensor to the control, identify the positive

(4 to 20 mA) and ground (SIG COM) terminals on the

OAQ sensor. See Fig. 46. Connect the 4 to 20 mA

terminal to RTU Open terminal J4--5. Connect the SIG

COM terminal to RTU Open terminal J4--6. See Fig. 49.

4-20mA

SIG COM

J4-5

J4-6

OAQ Sensor/RH Sensor

24 VAC

C10739

Fig. 49 -- RTU Open / Outdoor CO

Sensor

(33ZCSENCO2) Connections

Smoke Detector/Fire Shutdown (FSD) —

On 580J units equipped with factory--installed Smoke

Detector(s), the smoke detector controller implements the

unit shutdown through its NC contact set connected to the

unit’s CTB input. The FSD function is initiated via the

smoke detector’s Alarm NO contact set. The RTU Open

controller communicates the smoke detector’s tripped status

to the BAS building control. See Fig. 38 and Fig. 39, the

RTU Open wiring schematics.

The

Fire

Shutdown

Switch

configuration,

MENU



Config



Inputs



input 5

, identifies the normally

open status of this input when there is no fire alarm.

Space Humidity Sensor or Humidistat —
NOTE

: The accessory space relative humidity sensor and

humidistat do not apply to Size 30 units.

Perfect Humidity

Control Wiring:

In units equipped

with the Perfect Humidity option there are two pink

(PNK) wires loose in the control box used to control the

dehumidification function of the unit. These pink wires

are meant to be tied to a space humidistat or thermidistat

on an electromechanical unit. On RTU Open equipped

units these pink wires must be connected to J11--7 & 8 to

allow the Open board to operate the dehumidification

function for the unit. Disconnect the J11 Phoenix style

connector from the board and use the plug screws to

secure the pink wires in pins 7 and 8, reconnect the plug

to the board at J11.

Relative Humidity Sensors (Space or Duct Mounted):

The accessory space humidity sensor (33ZCSENSRH-01)

or duct humidity sensor (33ZCSENDRH-01) is used to

measure the relative humidity of air within the space or

return air duct. The RH reading is used to control the

Perfect Humidity

option of the rooftop unit. For wiring

distances up to 500 ft (152 m), use a 3--conductor, 18 or

20 AWG shielded cable. The shield must be removed

from the sensor end of the cable and grounded at the unit

end. The current loop power for sensor is provided by the

RTU Open controller as 24vdc. Refer to the instructions

supplied with the RH sensor for the electrical

requirements and terminal locations. RTU Open

configurations must be changed after adding an RH

sensor. See Fig. 50 and 51 for typical RH sensor wiring.

J4--1 or J4--4 = 24vdc loop power

J4--2 or J4--5 = 4--20mA signal input

NOTE

: The factory default for dehumidification control

is normally open humidistat.

SW2

Vin

Gnd

MOUNTING
HOLES

WIRING
OPENING

Vin - J4-1 or J4-4 24Vdc
Io - J4-2 or J4-5 -20mA output

C11087

Fig. 50 -- Space Relative Humidity Sensor Typical Wiring

580J

Summary of Contents for 580J Series





















































Search results

Summary of Contents for 580J Series

Reviews:

Related manuals for 580J Series

Brands by name

Popular brands

Bryant 580J Series, Installation Instructions Manual

Search results

Summary of Contents for 580J Series

Reviews:

Related manuals for 580J Series

Brands by name

Popular brands