Bryant 580J Series Installation Instructions Manual Download Page 11

Page: 11 / 52

C12384

LOCATION

DIMENSION

CONDITION

36---in (914 mm)

• Recommended clearance for air flow and service

42---in (1067 mm)

• Recommended clearance for air flow and service

18---in (457 mm)

• No Convenience Outlet
• No Economizer

• No field installed disconnect on economizer hood side (Factory---installed disconnect installed).

36---in (914 mm)

• Convenience Outlet installed.
• Vertical surface behind servicer is electrically non---conductive (e.g.: wood, fiberglass).

42---in (1067 mm)

• Convenience Outlet installed.
• Vertical surface behind servicer is electrically conductive (e.g.: metal, masonry).

96---in (2438 mm)

• Economizer and/or Power Exhaust installed.
• Check for sources of flue products with 10 feet (3 meters) of economizer fresh air intake.

42---in (1067 mm)

• Recommended clearance for service.

NOTE:

Unit not designed to have overhead obstruction. Contact Application Engineering for guidance on any application planning

overhead obstruction or for vertical clearances.

Fig. 5 -- Service Clearance Dimensional Drawing

Table 1 – Operating Weights

580J*

UNIT LB (KG)

Base Unit

Novation™ Coil

1824 (829)

1839 (836)

1989 (904)

2118 (963)

N/A

RTPF Coil

1907 (867)

1922 (874)

2072 (942)

2197 (999)

2640 (1200)

Economizer

246 (112)

Powered Outlet

35 (16)

Perfect Humidity™ System

110 (50)

120 (54)

N/A

Curb

14---in/356 mm

240 (109)

255 (116)

24---in/610 mm

340 (154)

355 (161)

580J

Summary of Contents for 580J Series





















































Search results

Summary of Contents for 580J Series

Reviews:

Related manuals for 580J Series

Brands by name

Popular brands

Bryant 580J Series, Installation Instructions Manual

Search results

Summary of Contents for 580J Series

Reviews:

Related manuals for 580J Series

Brands by name

Popular brands