Bryant 580J Series Installation Instructions Manual Download Page 36

Page: 36 / 52

Communication Wiring -- Protocols

General —

Protocols are the communication languages spoken by

control devices. The main purpose of a protocol is to

communicate information in the most efficient method

possible. Different protocols exist to provide different

kinds of information for different applications. In the BAS

application, many different protocols are used, depending

on manufacturer. Protocols do not change the function of

a controller; just make the front end user different.

The RTU Open can be set to communicate on four

different protocols: BACnet, Modbus, N2, and LonWorks.

Switch 3 (SW3) on the board is used to set protocol and

baud rate. Switches 1 and 2 (SW1 and SW2) are used to

set the board’s network address. See Fig. 52 and 53 for

protocol switch settings and address switches. The 3rd

party connection to the RTU Open is through plug J19.

See Fig. 54 for wiring.

NOTE

: Power must be cycled after changing the SW1--3

switch settings.
Contact your Bryant applications engineer for more

detailed information on protocols, 3rd party wiring, and

networking.

SW3 Protocol Selection

PROTOCOL

DS8

DS7

DS6

DS5

DS4

DS3

DS2

DS1

BACnet MS/TP

(Master)

Unused

OFF

Select Baud Select Baud

Modbus

(Slave)

Unused

OFF

Select Baud Select Baud

(Slave)

Unused

OFF

LonWorks

Unused

OFF

NOTE:
DS = Dip Switch
BACnet MS/TP SW3 example shown

Baud Rate Selections

BAUD RATE

DS2

DS1

9600

OFF

19,200

OFF

38,400

OFF

76,800

C07166

Fig. 52 -- RTU Open SW3 Dip Switch Settings

C10815

Fig. 53 -- RTU Open Address Switches

C10816

Fig. 54 -- Network Wiring

580J

Summary of Contents for 580J Series





















































Search results

Summary of Contents for 580J Series

Reviews:

Related manuals for 580J Series

Brands by name

Popular brands

Bryant 580J Series, Installation Instructions Manual

Search results

Summary of Contents for 580J Series

Reviews:

Related manuals for 580J Series

Brands by name

Popular brands