BRUEL & KJAER PULSE 7788 Technical Documentation Manual Download Page 57

Page: 57 / 62

Index

Numerics

2-ch. telemetry

........................................................ 8

Troubleshooting

.............................................. 43

Accessories

Ground station measurements

........................ 7

Vehicle station measurements

...................... 17

Acquisition setup

............................................ 46, 49

Antenna characteristics

........................................ 35

Antenna mounting

............................................... 35

AO-0426

................................................................... 6

AO-0479

................................................................... 7

AO-1489

................................................................. 16

Base station

........................................................... 30

Battery module

................................................. 5, 16

BNC cable drum

...................................................... 8

Cable drum

.............................................................. 8

Chainlink fences

.................................................... 36

Cigarette lighter power splitter

................ 8, 14, 18

Components

Ground and vehicle stations

.......................... 15

Ground station only

.......................................... 5

Configure

Ground station + vehicle station

.................. 48

Ground s weather station

................ 45

Connect hardware

................................................ 47

Connect PC

............................................ 9, 21, 22, 24

with WLAN setup

............................................. 31

Connection module

.......................................... 5, 16

Data transfer

......................................................... 20

Setup

................................................................. 26

Database

................................................................ 46

DC power cable

.................................................... 16

Environmental parameters

.................................... 7

Export to database

............................................... 46

Frame

................................................................. 5, 16

Frequencies

........................................................... 32

Front end connection

.......................................... 10

Front end modules

........................................... 5, 16

GADI driver

.................................................. 9, 14, 46

GPS antenna

.......................................................... 15

Connection and positioning

.......................... 23

GPS locked

...................................................... 48, 49

GPS speed sensor

................................................. 17

Connection

....................................................... 24

Ground station

........................................................ 2

Components

................................................ 5, 15

Connections

..................................................... 10

Front end

............................................................ 5

Installing

............................................................. 9

Options

............................................................... 7

Troubleshooting

.............................................. 38

WLAN connection

........................................... 30

WLAN hardware

.............................................. 15

Ground temperature sensor

................................. 7

Connection and positioning

.......................... 14

Summary of Contents for PULSE 7788































































Search results

Summary of Contents for PULSE 7788

Reviews:

Related manuals for PULSE 7788

Brands by name

Popular brands

BRUEL & KJAER PULSE 7788, Technical Documentation Manual

Search results

Summary of Contents for PULSE 7788

Reviews:

Related manuals for PULSE 7788

Brands by name

Popular brands