BRUEL & KJAER PULSE 7788 Technical Documentation Manual Download Page 26

Page: 26 / 62

Note:

The Ground Station runs continuously and measures the acoustic signals, photocell

signals, radar and weather station data, if present. This information is continuously

broadcast to the Vehicle Station using a remote station server and client to manage the

data transfer. These two components control communication between the Ground

Station (server) and the Vehicle Station (client).

5.1.1

Measurement

Control

A measurement run is started on the Vehicle Station PC by the operator activating the

system then clicking start in the Vehicle Station measurement control interface or by

triggering with a vehicle-mounted photocell.
Fig.5.2 shows the measurement control interface in the software.

Fig.5.2

The

PBY

Vehicle

Pass

‐

software

module

during

operation

The measurement run is started on the Ground Station when the ground-mounted

photocells are triggered.
Fig.5.3 shows the interface of the dedicated Ground Station software. After setup, the

interface need not be monitored, as the software will run on its own.

Summary of Contents for PULSE 7788































































Search results

Summary of Contents for PULSE 7788

Reviews:

Related manuals for PULSE 7788

Brands by name

Popular brands

BRUEL & KJAER PULSE 7788, Technical Documentation Manual

Search results

Summary of Contents for PULSE 7788

Reviews:

Related manuals for PULSE 7788

Brands by name

Popular brands