BRUEL & KJAER PULSE 7788 Technical Documentation Manual Download Page 15

Page: 15 / 62

Chapter

Installing

Ground

Station

Only

Configuration

A Ground Station only configuration is to be used with the

Standard

mode in the Pass-

by software.
Please see Chapter 2 for pictures and descriptions of the items to be installed in this

configuration.

3.1

Install

the

Pass

‐

Software

If you have received a factory-installed system:

1) Connect the front end to the PC using the supplied LAN cable.

2) Open the PULSE Pass-by application found under

All Programs\PULSE\Applications\Pass-

by\PBY Vehicle Pass-by

3) Follow the instructions provided in the software’s Help function for configuring the

system according to your test track specifications.

If you have not received a factory-installed system:

1) Install the PULSE software on your PC, including PULSE GADI Driver Type 3099-E if

you are using a Weather Station

2) Once PULSE is installed, run the Front-end Setup program found under

All

Programs\PULSE\Applications\Front-end Setup

and follow the on-screen

instructions on how to connect and configure LAN-XI hardware.

3) If there is no PULSE license installed on your system, follow the instructions given in

the PULSE License Installation manual, BE 1693.

4) Open the PULSE Pass-by application found under

All Programs\PULSE\Applications\Pass-

by\PBY Vehicle Pass-by

5) Follow the instructions provided in the software’s Help function for configuring the

system according to your test track specifications.

Summary of Contents for PULSE 7788































































Search results

Summary of Contents for PULSE 7788

Reviews:

Related manuals for PULSE 7788

Brands by name

Popular brands

BRUEL & KJAER PULSE 7788, Technical Documentation Manual

Search results

Summary of Contents for PULSE 7788

Reviews:

Related manuals for PULSE 7788

Brands by name

Popular brands