manualshive.com logo in svg

Brother HL-660 Series, User Manual

Share
Download
Brother HL-660 Series User Manual Download Page 9

USER’S GUIDE

viii

English

IEC 825 Laser Class (For 220–240 V Model Only)

CLASS 1 LASER PRODUCT.
APPAREIL Å LASER DE CLASSE 1.
LASER KLASSE 1
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
KLASS 1 : LASER
KLASSE 1 LASER PRODUKT

For Finland and Sweden

Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa
altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.

Varning – Om apparaten används på annat sätt än i denna Bruksanvisning specificerats, kan
användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.

The following caution label is attached near the scanner unit.

Disconnect device

The equipment must be installed near the socket outlet which must be easily accessible.

Manufactured at

Brother Industries Ltd.
Kariya Plant
1-5, Kitajizoyama, Noda-cho, Kariya-shi, Aichi-ken 448, Japan.

Manufacturing at Kariya Plant is carried out under a Quality System which is registered by
JQA Quality Assurance and BSI Quality Assuarance.

JQA Certificate of Registration No. 0340.
BSI Certificate of Registration No. FM27391

Summary of Contents for HL-660 Series

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands