manualshive.com logo in svg

Brother HL-660 Series, User Manual

Share
Download
Brother HL-660 Series User Manual Download Page 76

USER’S GUIDE

Appendix–2

English

Functions

CPU

MC68EC020 25 MHz

Emulation 

Automatic emulation selection among HP LaserJet 4 (PCL
level 5e), EPSON FX-850, or IBM Proprinter XL
BR-Script 2 is optionally available. (pre-installed in some
countries.)

Printer Driver

Windows 3.1 driver, supporting bi-directional capability
TrueType™ compatible screen-fonts for Microsoft Windows

Interface

Bi-directional parallel
AppleTalk interface is optionally available.  (Pre-installed in
some countries.)

Memory

2.0 MB (subject to the printer model)
Expandable up to 10 MB with industry standard SIMMs.

Control Panel

2 switches and 4 lamps

Diagnostics

Self-diagnostic program

Electrical and Mechanical

Power Source

U.S.A. and Canada:

AC 110 to 120 V, 60 Hz

Europe and Australia:

AC 220 to 240 V, 50 Hz

Power Consumption

Printing:

480 W or less

Stand-by:

55 W or less

Sleep:

12 W or less

Noise

Printing:

50 dB A or less

Stand-by:

41 dB A or less

Temperature

Operating:

10 to 32.5°C (59 to 90.5°F)

Storage:

0 to 40°C (38 to 104°F)

Humidity

Operating:

20 to 80% (without condensation)

Storage:

20 to 80% (without condensation)

Dimensions (W x H x D)

364.9 x 182.5 x 362.8 mm (14.4 x 7.2 x 14.3 inches)

(when the output tray is closed and the Multi-purpose sheet
feeder is removed.)

Weight

Approx. 7.5 kg (16.6 lbs.)

Summary of Contents for HL-660 Series

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands