manualshive.com logo in svg

Brother HL-660 Series, User Manual

Share
Download
Brother HL-660 Series User Manual Download Page 38

USER’S GUIDE

4–2

English

APPLETALK INTERFACE BOARD

To connect the printer to an Apple Macintosh computer, you need to
install the optional AppleTalk interface board. When you have installed
an AppleTalk interface board, you can share your printer between a DOS
computer and an Apple Macintosh using the parallel and AppleTalk
interfaces at the same time. Automatic interface selection is a standard
feature.  For the printer to be functional  with an Apple Macintosh,  you
need to install the BR-Script 2 ROM board.

✒

  Note

The AppleTalk interface board and BR-Script 2 ROM board for this
printer are optional, but in some countries these options may have been
installed by either the factory or dealer.

The AppleTalk interface board is installed onto the main controller board
inside the printer. For details about installation or connecting the cables,
see the instruction guide which is provided with the AppleTalk interface
board.

Summary of Contents for HL-660 Series

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands