manualshive.com logo in svg

Brother HL-660 Series, User Manual

Share
Download
Brother HL-660 Series User Manual Download Page 31

CHAPTER 3 CONTROL PANEL

3–3

English

SWITCHES

This printer has the following control panel switches.

Fig. 3-2 Switches on Control Panel

✒

  Note

This printer has no power switch. You just plug the power cord into the
AC outlet. The sleep mode feature handles all power control. For more
information on sleep mode, see “OTHER CONTROL FEATURES” in
this chapter.

SELECT (RESET) Switch

The lower switch on the control panel can work as the SELECT or
RESET switch.

SELECT Switch

The SELECT switch alternately turns the printer on-line and off-line.
When the printer is on-line, the READY lamp is on. When the printer is
off-line, the READY lamp is blinking.

If you press the SELECT switch during printing, the printer immediately
stops printing even if the printer has started to print. It ejects the page,
and then enters the off-line status. Press the SELECT switch again and
the printer will reprint the complete page.

Summary of Contents for HL-660 Series

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands