manualshive.com logo in svg

Brother HL-1070, Service Manual

Share
Download
Brother HL-1070 Service Manual Download Page 207

CHAPTER 5 MAINTENANCE

5–11

CLEANING THE PRINTER

Clean the printer exterior and interior periodically. If printed pages get
stained with toner, clean the printer interior and drum unit.

Cleaning the Printer Exterior

Clean the printer exterior as follows:

1. Turn off the power switch and unplug the power cord.

 Warning

There are high voltage electrodes inside the printer. Before cleaning
the printer, make sure to turn off the power switch and unplug the
power cord from the power outlet

Fig. 5-19 Turning off the Switch and Unplugging

2. Remove the paper in the multi-purpose sheet feeders.

3. Use a damp cloth for cleaning.

!

Caution

Use water or neutral detergents for cleaning. Cleaning with volatile
liquids such as thinners or benzene will damage the surface of the printer.

4. Wipe dirt and dust away from the printer exterior and feeders with a

cloth.

5. Load paper into the multi-purpose sheet feeders, and plug in the

power cord.

Summary of Contents for HL-1070





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands