manualshive.com logo in svg

Brother HL-1070, Service Manual

Share
Download
Brother HL-1070 Service Manual Download Page 156

Definitions of Warnings, Cautions, and Notes

The following conventions are used in this User’s Guide:

 

Warning

Indicates warnings that must be observed to prevent possible
personal injury.

!

Caution

Indicates cautions that must be observed to use the printer properly or
prevent damage to the printer.

✒

Note

Indicates notes and useful tips to remember when using the printer.

To Use the Printer Safely

 

Warning

After you have just used the printer, some internal parts of the
printer are extremely hot. When you open the top cover of the
printer, never touch the shaded parts shown in the following
illustration.

 

High Temperature

Inside the Printer

 

Warning

There are high voltage electrodes inside the printer. Before cleaning
the printer, make sure to turn off the power switch and unplug the
power cord from the power outlet.

Turning off the Switch and Unplugging the Printer

Summary of Contents for HL-1070





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands