manualshive.com logo in svg

Brother HL-1070, Service Manual

Share
Download
Brother HL-1070 Service Manual Download Page 206

USER’S GUIDE

5–10

ADJUSTING THE PRINT DENSITY

The print density dial is located inside the printer. You can use it to adjust
the amount of toner applied to the paper.

When the toner cartridge and drum unit are replaced, or if the operating
temperature and humidity are high or low, print conditions may change
causing darker or lighter printouts.

Use a screwdriver to turn the print density dial gently clockwise for
darker printouts and counterclockwise for lighter printouts. The dial has
been factory set to the middle position.

Lighter

Darker

Fig. 5-17 Adjusting the Print Density Dial

 

Warning

After you have just used the printer, some internal parts of the
printer are extremely hot. When you open the top cover of the
printer, never touch the shaded parts shown in the following
illustration.

 

High Temperature

Fig. 5-18 Inside the Printer

Summary of Contents for HL-1070





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands