Brother FAX-575 User Manual Download | Manualshive

Page: 88 / 114

background image

11 - 2

Important information

If trouble is experienced with this equipment, for repair or warranty
information, please contact Brother Customer Service. (See

Brother numbers

on page i.) If the equipment is causing harm to

the telephone network, the telephone company may request that
you disconnect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact
the state public utility commission, public service commission or
corporation commission for information.

If your home has specially wired alarm equipment connected to the
telephone line, ensure the installation of this equipment does not
disable your alarm equipment. If you have questions about what
will disable alarm equipment, call your telephone company or a
qualified installer.

If you are not able to solve a problem with the fax machine, call
Brother Customer Service. (See

Brother numbers

WARNING

For protection against the risk of electrical shock, always
disconnect all cables from the wall outlet before servicing,
modifying or installing the equipment.

This equipment may not be used on coin service lines provided by
the telephone company or connected to party lines.

Brother cannot accept any financial or other responsibilities that
may be the result of your use of this information, including direct,
special or consequential damages. There are no warranties
extended or granted by this document.

WARNING

This fax machine has been certified to comply with FCC standards,
which are applied to the USA only. A grounded plug should be
plugged into a grounded AC outlet after checking the rating of the
local power supply for the fax machine to operate properly and
safely.

Federal Communications Commission (FCC)
Declaration of Conformity (USA only)

declares, that the products

Product Name: FAX575

comply with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.

Responsible Party:

Brother International Corporation

100 Somerset Corporate Boulevard

Bridgewater, NJ 08807-0911 USA

TEL: (908) 704-1700

«
...
86
87
88
89
90
...
»

Summary of Contents for FAX-575



















































































































Reviews:

No comments

Related manuals for FAX-575

Brand: Xerox Pages: 22

Brand: Consew Pages: 42

KING COBRA 310-CSA

Brand: U.S. Products Pages: 16

Brand: Viper Pages: 93

Brand: Pacific Pages: 8

Brand: A-S-S Pages: 7

Brand: MyBinding Pages: 7

Brand: Euro-Pro Pages: 56

Brand: JUKI Pages: 128

Brand: JUKI Pages: 59

LBH-1790A Series

Brand: JUKI Pages: 5

Brand: JUKI Pages: 33

Brand: Canon Pages: 65

Brand: Canon Pages: 17

Brand: Canon Pages: 16

Brand: Canon Pages: 185

i-Sensys FAX-L3000

Brand: Canon Pages: 8

Brand: Canon Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands