Brother 970MC - MFC B/W - All-in-One Owner'S Manual Download Page 17

Page: 17 / 165

C H A P T E R T W O

Installation

Caution

Never install telephone wiring during a lightning storm.

We recommend that this product be used with a surge protection device
to protect the product against lightning storms.

Never install a telephone jack in a wet location unless the jack is
specifically designed for a wet location.

Never touch telephone wires or terminals that are not insulated unless
the telephone line has been disconnected at the network interface.

Use caution when installing or modifying telephone lines.

Avoid using a telephone (other than a cordless type) during an electri-
cal storm. There may be a remote risk of electric shock from lightning.

Do not use the telephone to report a gas leak in the vicinity of the leak.

For PLUGGABLE EQUIPMENT, the socket-outlet should be installed
near the equipment and should be easily accessible.

Summary of Contents for 970MC - MFC B/W - All-in-One






































































































































































Search results

Summary of Contents for 970MC - MFC B/W - All-in-One

Reviews:

Related manuals for 970MC - MFC B/W - All-in-One

Brands by name

Popular brands

Brother 970MC - MFC B/W - All-in-One, Owner'S Manual

Search results

Summary of Contents for 970MC - MFC B/W - All-in-One

Reviews:

Related manuals for 970MC - MFC B/W - All-in-One

Brands by name

Popular brands